







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Vallejo Owner’s Guide
We install Schluter profile and drainage systems for driveways and pavers in Vallejo, and the honest installed price for the profiles, edge restraints, and drainage channel work typically lands between $7,000 and $18,000 when it’s part of a full paver driveway job. The parts themselves – Schluter edging profiles, KERDI-LINE drainage components, and edge restraint trim – usually run a small fraction of that; labor and prep are what move the number. Owners almost always find out something’s wrong the same way: a paver edge starts walking out of line after a wet winter, the drainage channel backs up and pools water against the garage slab, or the trim at the driveway apron lifts and catches a tire.

Key Takeaways
- A failing Schluter edge profile or drainage component usually shows up as movement, pooling, or lifted trim – not a sudden break.
- Schluter’s profiles are dimension-specific. The wrong height or series won’t seat flush and will fail again.
- We’re an independent contractor. We source Schluter parts to spec, but we’re not affiliated with Schluter.
- Vallejo’s clay-heavy soils and wet winters punish poor edge restraint faster than dry inland climates do.
Which Schluter Models This Applies To

Schluter doesn’t make one generic driveway part. The profiles you’ll actually encounter on a Vallejo driveway or paver job fall into a few families, and getting the right one matters more than most homeowners expect.
Edge and transition profiles like the FINEC, QUADEC, and SCHIENE lines are meant to finish and protect tile and paver edges. They’re sized by height – 8mm, 10mm, 12.5mm, and so on – and by material (anodized aluminum, stainless, PVC). If your pavers sit at a different finished thickness than the profile was specced for, the trim won’t sit flush. That’s the single most common compatibility gotcha we see. Drainage and linear channel systems, including KERDI-LINE and the TROBA family of drainage mats, are sized by channel width and grate load rating; a driveway channel needs a load-rated grate, and a pedestrian-rated one will deform under a vehicle. Stair-nosing and apron profiles finish driveway transitions and step edges.
To identify the right part, pull the label from any intact original trim (Schluter stamps the series and dimensions on the profile itself in most cases), or measure the finished paver height at the edge with a caliper – not a tape measure. On the OEM-versus-aftermarket call: Schluter’s own profiles have a specific alloy and finish that holds up better at the driveway than generic aluminum trim, so for the exposed edge we spec the OEM part. For hidden drainage matting, a quality equivalent is often fine. Bradford Remodeling works with a documented brand roster – KraftMaid, Cambria, Silestone and others – and sources Schluter to spec the same way.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
These are the symptoms we see on Vallejo driveways, and what’s actually causing each one.
- Edge profile lifting or rocking. The profile has lost its mechanical bond to the substrate, usually because the base wasn’t compacted or the adhesive failed. Once it rocks, water gets under it and the failure accelerates.
- Water pooling against the garage or apron. The drainage channel or slope isn’t shedding water. In Vallejo this often traces to a channel that was set at the wrong fall or a grate that’s clogged with grit and leaf litter.
- Pavers walking out of line at the edge. The edge restraint has given way. Without a solid restraint, the outer course creeps outward every freeze-thaw and wet-season cycle.
- Trim catching a tire or tripping a foot. A profile that’s the wrong height for the finished paver sits proud of the surface and becomes a snag point. This is a sizing error, not wear.
- Rust streaks or finish flaking on the trim. A cheaper alloy or a scratched anodized finish breaking down. In Vallejo’s wet winters, an under-specced profile corrodes faster than the stainless or quality aluminum Schluter line.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s how the numbers break down for Vallejo, and these are installed prices, not parts-only.
| Scope | Installed Price Range |
|---|---|
| Paver driveway installation (full job, includes edge profiles and restraint) | $7,000 – $18,000 |
| Paver patio installation (profile and drainage work) | $3,500 – $11,000 |
| Driveway sealing (protects paver and profile edges) | $250 – $700 |
| Driveway replacement (full tear-out and rebuild) | $5,000 – $14,000 |
What drives the range: driveway square footage, whether the base needs re-compaction, how many linear feet of profile and channel are involved, and the load rating on drainage grates. We give you a written price before work begins – always – broken into parts-and-materials versus labor, so you can see exactly what the Schluter components cost against the install. No numbers that move at the door. Every completed job is covered by the 365-Day Done Right Promise: if the work fails inside a full year, we come back and correct it at no charge. Free estimate to start.
DIY or Call Us?
Some things you can check safely yourself. Walk the edge and feel for any profile that rocks underfoot. Clear grit and leaf litter out of the drainage grate so you can see whether water still pools. Measure the finished paver height at a lifted edge with a caliper and compare it to what the original profile was specced for. Take a photo.
Where DIY goes wrong: re-seating an edge profile or re-setting a drainage channel means lifting pavers, re-compacting base, and re-bonding to a clean substrate – and if the base is the problem, gluing the trim back down just buys you one more wet season. A profile set at the wrong height or a channel set at the wrong fall will fail again no matter how well you stick it. That’s the point where it’s worth a call. Our technicians have up to 22 years of experience with these systems, and they’re background-checked and uniformed – you know who’s coming before the crew arrives. Call (844) 560-4789 and we’ll schedule a free estimate.
FAQs

A properly installed Schluter edge profile or linear drainage system should hold up for the life of the paver installation – decades, not years – as long as the base was compacted and the profile was correctly sized. The weak point isn’t the Schluter part itself; it’s the substrate and the install. In Vallejo, poorly compacted clay base and wet-season movement are what shorten the life, and that’s what our 365-Day Done Right Promise is built to back.
Sometimes yes. A clogged drainage grate just needs clearing. A single lifted edge profile can often be re-seated if the base under it is still sound. But if pavers are walking out of line or water is pooling against the slab, the underlying cause is the base or the slope, and a repair that doesn’t fix that will fail again. We’ll tell you honestly which situation you’re in during the estimate. Call (844) 560-4789 for a free look.
A single edge profile re-set can be a half-day job; a drainage channel or a section of edge restraint running the length of the driveway is typically one to three days depending on how much paver has to come up and whether the base needs re-work. We put the timeline in writing before any work starts.
We measure the finished paver height and drain load requirement, match the Schluter series and dimension, and source the OEM part to spec through our documented supplier relationships. Bradford Remodeling is an independent contractor – we’re not affiliated with Schluter, and we don’t stock parts on a truck or hold inventory. We order to your job’s measurements. Call (844) 560-4789 to schedule your free estimate.
Written by the team at Bradford Remodeling Co Vallejo, serving Vallejo and nearby areas.












