







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Fence Installation: The Vallejo Owner’s Guide
Fence installation using Tamko-approved components in Vallejo typically runs $3,500 to $9,000 installed, depending on linear footage, fence height and site conditions, and we schedule most installs within a week of an accepted written estimate. Owners usually come to us after a gate sags and catches, a post starts to lean, or pickets warp and split after a couple of wet winters. What looked like a small repair turns out to be a system failing at the posts or fasteners, and that’s the point where a straight answer about replacement beats another patch.

We’re Bradford Remodeling Co Vallejo, and we install fences built on Tamko-rated materials. We are an independent contractor, not affiliated with Tamko. Every job starts with a written price, and every finished install carries our 365-Day Done Right Promise.
Key Takeaways
- Installed Tamko-rated fence work in Vallejo: $3,500 to $9,000.
- Most post-and-fastener failures trace back to soil movement and moisture, not the fence panels.
- Written price before any work starts, no numbers that move at the door.
- 365-Day Done Right Promise on every completed install.
Which Tamko Models This Applies To

Tamko makes roofing and waterproofing products, and its name gets attached to fence systems and fence accessory lines sold through lumber yards and building suppliers. So the first job is confirming exactly which Tamko product line you have, because the specs don’t carry across lines. Check the label on the post, rail or picket bundle, or the stamp on the fastener packaging; most carry a series code and a nominal dimension. Measure what you have – rail thickness, picket width, post gauge – before you buy anything.
The Tamko compatibility gotcha we run into constantly in Vallejo: nominal sizing isn’t real sizing. A “6-foot” fence panel or a “2×4” rail can be off a fraction from what’s on your existing run, and that fraction is enough to throw off gate alignment, rail spacing and fastener fit. Match by measured dimension, not by the name on the box.
On the OEM-versus-aftermarket question, here’s how we think about it. For visible components like pickets and rails, a quality aftermarket equivalent that matches the measured dimension and material grade is often the honest choice: same function, better price, no compromise. For structural parts – posts, brackets, hinges and latches – we lean toward the manufacturer-spec part, because that’s where load and weather do their damage. Bring us the label or the measurement and we’ll tell you which way to go.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Fence Installation Is Failing
These are the symptoms we see most often on Vallejo fences. Each one points to a specific cause, and the fix depends on which part is actually giving out.
- Sagging gates that drag or won’t latch. The hinge and post are taking the load, and the post is probably settling or the hinge screws have pulled. A gate that sags is a structural warning, not a cosmetic one.
- Leaning or loose posts. Post footings shift with soil movement and seasonal moisture. Once a post loses its footing, no amount of re-nailing brings the run back to true.
- Split, warped or checked pickets. Material that dries unevenly cups and splits. That’s a material and grade question, and it usually means the original install used a lower-grade picket than the job called for.
- Rust bleeding at fasteners and brackets. Coating failures on the hardware show up before the panels fail. Rust at the fasteners is the first sign the assembly is loosening.
- Rails pulling loose from posts. Fastener pull-out, usually from undersized hardware or a post that’s no longer holding. This is the failure that makes a whole run unsafe.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Vallejo, installed Tamko-rated fence work runs $3,500 to $9,000. The range is driven by linear footage, fence height, gate count, post-footing conditions and how much existing fence has to come out first. A simple run on good ground lands near the bottom; a long stretch with several gates and tough footings lands near the top.
What we put in the written price:
- Materials, with the specific product and grade listed by name.
- Labor, including removal of the old run and post work.
- Gate hardware and fasteners matched to the fence specs.
- Cleanup and haul-away.
That number is the number. It doesn’t move at the door. And when the job closes, you get a signed written copy of our 365-Day Done Right Promise: if the work fails within a year, we come back and correct it at no charge.
DIY or Call Us?
Here’s the honest split. You can safely inspect your own fence: walk the run, push on each post, check gates for sag and drag, look at fasteners for rust, and confirm the Tamko label on the materials you have. That’s useful, and it tells us a lot before we ever quote.
Where DIY goes wrong is the post work and the structural connections. Digging and setting footings to the right depth, aligning a run true, and getting gates to hang square under load is where a weekend project turns into a second install. Fence failure is often dangerous too – a heavy leaning post or a gate that comes off its hinge can hurt someone. If your posts are loose or your gates are coming apart, stop patching. Call us at (844) 560-4789, and we’ll give you a written price before anything starts.
FAQs

A properly installed fence on good footings should hold 10 to 15 years, and often longer with maintenance, but Vallejo’s wet winters and dry summers work the posts and fasteners hard, so post footings and gate hardware are the first things to go, not the panels. Call (844) 560-4789 for a straight answer on your specific run – estimates are free.
Sometimes yes. A single failing gate, a few loose fasteners or one damaged panel can often be repaired. But once posts are leaning or rails are pulling loose, a repair is usually a patch over a failing structure. We’ll tell you which one you actually have in the written estimate – no upselling.
Most residential fence installs run one to three days on site, depending on footage and footing conditions. Removal and post work are usually the long part. We give you the schedule in writing before we start.
We source from the manufacturer or an authorized supplier based on the model and measured dimension you have. You get the exact product specified in writing before we order, so you know what’s going into your yard.
Ready to get your fence squared away? Call Bradford Remodeling Co Vallejo at (844) 560-4789 for a free estimate. We answer live, 24/7. We also work with KraftMaid, Cambria and Silestone on interior projects, and every job comes with a written price and our 365-Day Done Right Promise.
Written by the team at Bradford Remodeling Co Vallejo, serving Vallejo and nearby areas.












